-some pins as I"m using a arduino nano.
Code: Select all
/*
Example code compatible with the Lambda Shield for Arduino.
Copyright (C) 2017 - 2020 Bylund Automotive AB.
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
Contact information of author:
http://www.bylund-automotive.com/
info@bylund-automotive.com
Version history:
2017-12-30 v1.0.0 First release to GitHub.
2018-10-25 v1.1.0 Implemented an improved lambda conversion.
2019-04-19 v1.2.0 Implemented an improved oxygen conversion.
2019-06-26 v1.3.0 Adjusted PID regulation of heater.
2019-07-14 v1.3.1 Modified Lookup_Lambda() function.
2019-07-14 v1.4.0 Implemented an analog output function.
2020-03-26 v1.4.1 Optimized analog output function.
*/
//Define included headers.
#include <SPI.h>
//Define CJ125 registers used.
#define CJ125_IDENT_REG_REQUEST 0x4800 /* Identify request, gives revision of the chip. */
#define CJ125_DIAG_REG_REQUEST 0x7800 /* Dignostic request, gives the current status. */
#define CJ125_INIT_REG1_REQUEST 0x6C00 /* Requests the first init register. */
#define CJ125_INIT_REG2_REQUEST 0x7E00 /* Requests the second init register. */
#define CJ125_INIT_REG1_MODE_CALIBRATE 0x569D /* Sets the first init register in calibration mode. */
#define CJ125_INIT_REG1_MODE_NORMAL_V8 0x5688 /* Sets the first init register in operation mode. V=8 amplification. */
#define CJ125_INIT_REG1_MODE_NORMAL_V17 0x5689 /* Sets the first init register in operation mode. V=17 amplification. */
#define CJ125_DIAG_REG_STATUS_OK 0x28FF /* The response of the diagnostic register when everything is ok. */
#define CJ125_DIAG_REG_STATUS_NOPOWER 0x2855 /* The response of the diagnostic register when power is low. */
#define CJ125_DIAG_REG_STATUS_NOSENSOR 0x287F /* The response of the diagnostic register when no sensor is connected. */
#define CJ125_INIT_REG1_STATUS_0 0x2888 /* The response of the init register when V=8 amplification is in use. */
#define CJ125_INIT_REG1_STATUS_1 0x2889 /* The response of the init register when V=17 amplification is in use. */
//Define pin assignments.
#define CJ125_NSS_PIN 7 /* Pin used for chip select in SPI communication. */
#define LED_STATUS_POWER 5 /* Pin used for power the status LED, indicating we have power. */
#define LED_STATUS_HEATER 6 /* Pin used for the heater status LED, indicating heater activity. */
#define HEATER_OUTPUT_PIN 9 /* Pin used for the PWM output to the heater circuit. */
#define ANALOG_OUTPUT_PIN 11 /* Pin used for the PWM to the 0-1V analog output. */
#define UB_ANALOG_INPUT_PIN A2 /* Analog input for power supply.*/
#define UR_ANALOG_INPUT_PIN A0 /* Analog input for temperature.*/
#define UA_ANALOG_INPUT_PIN A1 /* Analog input for lambda.*/
//Define adjustable parameters.
#define SERIAL_RATE 1 /* Serial refresh rate in HZ (1-100)*/
#define UBAT_MIN 550 /* Minimum voltage (ADC value) on Ubat to operate */
//Global variables.
int adcValue_UA = 0; /* ADC value read from the CJ125 UA output pin */
int adcValue_UR = 0; /* ADC value read from the CJ125 UR output pin */
int adcValue_UB = 0; /* ADC value read from the voltage divider caluclating Ubat */
int adcValue_UA_Optimal = 0; /* UA ADC value stored when CJ125 is in calibration mode, λ=1 */
int adcValue_UR_Optimal = 175; /* UR ADC value stored when CJ125 is in calibration mode, optimal temperature */
int HeaterOutput = 0; /* Current PWM output value (0-255) of the heater output pin */
int serial_counter = 0; /* Counter used to calculate refresh rate on the serial output */
int CJ125_Status = 0; /* Latest stored DIAG registry response from the CJ125 */
//PID regulation variables.
int dState; /* Last position input. */
int iState; /* Integrator state. */
const int iMax = 250; /* Maximum allowable integrator state. */
const int iMin = -250; /* Minimum allowable integrator state. */
const float pGain = 120; /* Proportional gain. Default = 120*/
const float iGain = 0.8; /* Integral gain. Default = 0.8*/
const float dGain = 10; /* Derivative gain. Default = 10*/
//Lambda Conversion Lookup Table. (ADC 39-791).
const PROGMEM float Lambda_Conversion[753] {
0.750, 0.751, 0.752, 0.752, 0.753, 0.754, 0.755, 0.755, 0.756, 0.757, 0.758, 0.758, 0.759, 0.760, 0.761, 0.761, 0.762, 0.763, 0.764, 0.764,
0.765, 0.766, 0.766, 0.767, 0.768, 0.769, 0.769, 0.770, 0.771, 0.772, 0.772, 0.773, 0.774, 0.774, 0.775, 0.776, 0.777, 0.777, 0.778, 0.779,
0.780, 0.780, 0.781, 0.782, 0.782, 0.783, 0.784, 0.785, 0.785, 0.786, 0.787, 0.787, 0.788, 0.789, 0.790, 0.790, 0.791, 0.792, 0.793, 0.793,
0.794, 0.795, 0.796, 0.796, 0.797, 0.798, 0.799, 0.799, 0.800, 0.801, 0.802, 0.802, 0.803, 0.804, 0.805, 0.805, 0.806, 0.807, 0.808, 0.808,
0.809, 0.810, 0.811, 0.811, 0.812, 0.813, 0.814, 0.815, 0.815, 0.816, 0.817, 0.818, 0.819, 0.820, 0.820, 0.821, 0.822, 0.823, 0.824, 0.825,
0.825, 0.826, 0.827, 0.828, 0.829, 0.830, 0.830, 0.831, 0.832, 0.833, 0.834, 0.835, 0.836, 0.837, 0.837, 0.838, 0.839, 0.840, 0.841, 0.842,
0.843, 0.844, 0.845, 0.846, 0.846, 0.847, 0.848, 0.849, 0.850, 0.851, 0.852, 0.853, 0.854, 0.855, 0.855, 0.856, 0.857, 0.858, 0.859, 0.860,
0.861, 0.862, 0.863, 0.864, 0.865, 0.865, 0.866, 0.867, 0.868, 0.869, 0.870, 0.871, 0.872, 0.873, 0.874, 0.875, 0.876, 0.877, 0.878, 0.878,
0.879, 0.880, 0.881, 0.882, 0.883, 0.884, 0.885, 0.886, 0.887, 0.888, 0.889, 0.890, 0.891, 0.892, 0.893, 0.894, 0.895, 0.896, 0.897, 0.898,
0.899, 0.900, 0.901, 0.902, 0.903, 0.904, 0.905, 0.906, 0.907, 0.908, 0.909, 0.910, 0.911, 0.912, 0.913, 0.915, 0.916, 0.917, 0.918, 0.919,
0.920, 0.921, 0.922, 0.923, 0.924, 0.925, 0.926, 0.927, 0.928, 0.929, 0.931, 0.932, 0.933, 0.934, 0.935, 0.936, 0.937, 0.938, 0.939, 0.940,
0.941, 0.942, 0.944, 0.945, 0.946, 0.947, 0.948, 0.949, 0.950, 0.951, 0.952, 0.953, 0.954, 0.955, 0.957, 0.958, 0.959, 0.960, 0.961, 0.962,
0.963, 0.965, 0.966, 0.967, 0.969, 0.970, 0.971, 0.973, 0.974, 0.976, 0.977, 0.979, 0.980, 0.982, 0.983, 0.985, 0.986, 0.987, 0.989, 0.990,
0.991, 0.992, 0.994, 0.995, 0.996, 0.998, 0.999, 1.001, 1.003, 1.005, 1.008, 1.010, 1.012, 1.015, 1.017, 1.019, 1.022, 1.024, 1.026, 1.028,
1.030, 1.032, 1.035, 1.037, 1.039, 1.041, 1.043, 1.045, 1.048, 1.050, 1.052, 1.055, 1.057, 1.060, 1.062, 1.064, 1.067, 1.069, 1.072, 1.075,
1.077, 1.080, 1.082, 1.085, 1.087, 1.090, 1.092, 1.095, 1.098, 1.100, 1.102, 1.105, 1.107, 1.110, 1.112, 1.115, 1.117, 1.120, 1.122, 1.124,
1.127, 1.129, 1.132, 1.135, 1.137, 1.140, 1.142, 1.145, 1.148, 1.151, 1.153, 1.156, 1.159, 1.162, 1.165, 1.167, 1.170, 1.173, 1.176, 1.179,
1.182, 1.185, 1.188, 1.191, 1.194, 1.197, 1.200, 1.203, 1.206, 1.209, 1.212, 1.215, 1.218, 1.221, 1.224, 1.227, 1.230, 1.234, 1.237, 1.240,
1.243, 1.246, 1.250, 1.253, 1.256, 1.259, 1.262, 1.266, 1.269, 1.272, 1.276, 1.279, 1.282, 1.286, 1.289, 1.292, 1.296, 1.299, 1.303, 1.306,
1.310, 1.313, 1.317, 1.320, 1.324, 1.327, 1.331, 1.334, 1.338, 1.342, 1.345, 1.349, 1.352, 1.356, 1.360, 1.364, 1.367, 1.371, 1.375, 1.379,
1.382, 1.386, 1.390, 1.394, 1.398, 1.401, 1.405, 1.409, 1.413, 1.417, 1.421, 1.425, 1.429, 1.433, 1.437, 1.441, 1.445, 1.449, 1.453, 1.457,
1.462, 1.466, 1.470, 1.474, 1.478, 1.483, 1.487, 1.491, 1.495, 1.500, 1.504, 1.508, 1.513, 1.517, 1.522, 1.526, 1.531, 1.535, 1.540, 1.544,
1.549, 1.554, 1.558, 1.563, 1.568, 1.572, 1.577, 1.582, 1.587, 1.592, 1.597, 1.601, 1.606, 1.611, 1.616, 1.621, 1.627, 1.632, 1.637, 1.642,
1.647, 1.652, 1.658, 1.663, 1.668, 1.674, 1.679, 1.684, 1.690, 1.695, 1.701, 1.707, 1.712, 1.718, 1.724, 1.729, 1.735, 1.741, 1.747, 1.753,
1.759, 1.764, 1.770, 1.776, 1.783, 1.789, 1.795, 1.801, 1.807, 1.813, 1.820, 1.826, 1.832, 1.839, 1.845, 1.852, 1.858, 1.865, 1.872, 1.878,
1.885, 1.892, 1.898, 1.905, 1.912, 1.919, 1.926, 1.933, 1.940, 1.947, 1.954, 1.961, 1.968, 1.975, 1.983, 1.990, 1.997, 2.005, 2.012, 2.020,
2.027, 2.035, 2.042, 2.050, 2.058, 2.065, 2.073, 2.081, 2.089, 2.097, 2.105, 2.113, 2.121, 2.129, 2.137, 2.145, 2.154, 2.162, 2.171, 2.179,
2.188, 2.196, 2.205, 2.214, 2.222, 2.231, 2.240, 2.249, 2.258, 2.268, 2.277, 2.286, 2.295, 2.305, 2.314, 2.324, 2.333, 2.343, 2.353, 2.363,
2.373, 2.383, 2.393, 2.403, 2.413, 2.424, 2.434, 2.444, 2.455, 2.466, 2.476, 2.487, 2.498, 2.509, 2.520, 2.532, 2.543, 2.554, 2.566, 2.577,
2.589, 2.601, 2.613, 2.625, 2.637, 2.649, 2.662, 2.674, 2.687, 2.699, 2.712, 2.725, 2.738, 2.751, 2.764, 2.778, 2.791, 2.805, 2.819, 2.833,
2.847, 2.861, 2.875, 2.890, 2.904, 2.919, 2.934, 2.949, 2.964, 2.979, 2.995, 3.010, 3.026, 3.042, 3.058, 3.074, 3.091, 3.107, 3.124, 3.141,
3.158, 3.175, 3.192, 3.209, 3.227, 3.245, 3.263, 3.281, 3.299, 3.318, 3.337, 3.355, 3.374, 3.394, 3.413, 3.433, 3.452, 3.472, 3.492, 3.513,
3.533, 3.554, 3.575, 3.597, 3.618, 3.640, 3.662, 3.684, 3.707, 3.730, 3.753, 3.776, 3.800, 3.824, 3.849, 3.873, 3.898, 3.924, 3.950, 3.976,
4.002, 4.029, 4.056, 4.084, 4.112, 4.140, 4.169, 4.198, 4.228, 4.258, 4.288, 4.319, 4.350, 4.382, 4.414, 4.447, 4.480, 4.514, 4.548, 4.583,
4.618, 4.654, 4.690, 4.726, 4.764, 4.801, 4.840, 4.879, 4.918, 4.958, 4.999, 5.040, 5.082, 5.124, 5.167, 5.211, 5.255, 5.299, 5.345, 5.391,
5.438, 5.485, 5.533, 5.582, 5.632, 5.683 ,5.735, 5.788, 5.841, 5.896, 5.953, 6.010, 6.069, 6.129, 6.190, 6.253, 6.318, 6.384, 6.452, 6.521,
6.592, 6.665, 6.740, 6.817, 6.896, 6.976, 7.059, 7.144, 7.231, 7.320, 7.412, 7.506, 7.602, 7.701, 7.803, 7.906, 8.013, 8.122, 8.234, 8.349,
8.466, 8.587, 8.710, 8.837, 8.966, 9.099, 9.235, 9.374, 9.516, 9.662, 9.811, 9.963, 10.119
};
//Oxygen Conversion Lookup Table. (ADC 307-854).
const PROGMEM float Oxygen_Conversion[548] {
00.00, 00.04, 00.08, 00.13, 00.17, 00.21, 00.25, 00.30, 00.34, 00.38, 00.42, 00.47, 00.51, 00.55, 00.59, 00.64, 00.68, 00.72, 00.76, 00.81,
00.85, 00.89, 00.93, 00.98, 01.02, 01.06, 01.10, 01.15, 01.19, 01.23, 01.27, 01.31, 01.36, 01.40, 01.44, 01.48, 01.53, 01.57, 01.61, 01.65,
01.70, 01.74, 01.78, 01.82, 01.86, 01.91, 01.95, 01.99, 02.03, 02.08, 02.12, 02.16, 02.20, 02.24, 02.29, 02.33, 02.37, 02.41, 02.45, 02.50,
02.54, 02.58, 02.62, 02.66, 02.71, 02.75, 02.79, 02.83, 02.87, 02.92, 02.96, 03.00, 03.04, 03.08, 03.13, 03.17, 03.21, 03.25, 03.29, 03.33,
03.38, 03.42, 03.46, 03.50, 03.54, 03.58, 03.63, 03.67, 03.71, 03.75, 03.79, 03.83, 03.88, 03.92, 03.96, 04.00, 04.04, 04.08, 04.12, 04.17,
04.21, 04.25, 04.29, 04.33, 04.37, 04.41, 04.45, 04.50, 04.54, 04.58, 04.62, 04.66, 04.70, 04.74, 04.78, 04.82, 04.86, 04.91, 04.95, 04.99,
05.03, 05.07, 05.11, 05.15, 05.19, 05.23, 05.27, 05.31, 05.35, 05.39, 05.44, 05.48, 05.52, 05.56, 05.60, 05.64, 05.68, 05.72, 05.76, 05.80,
05.84, 05.88, 05.92, 05.96, 06.00, 06.04, 06.08, 06.12, 06.16, 06.20, 06.24, 06.28, 06.32, 06.36, 06.40, 06.44, 06.48, 06.52, 06.56, 06.60,
06.64, 06.68, 06.72, 06.76, 06.80, 06.84, 06.88, 06.92, 06.96, 07.00, 07.03, 07.07, 07.11, 07.15, 07.19, 07.23, 07.27, 07.31, 07.35, 07.39,
07.43, 07.47, 07.51, 07.55, 07.59, 07.62, 07.66, 07.70, 07.74, 07.78, 07.82, 07.86, 07.90, 07.94, 07.98, 08.02, 08.06, 08.09, 08.13, 08.17,
08.21, 08.25, 08.29, 08.33, 08.37, 08.41, 08.45, 08.49, 08.52, 08.56, 08.60, 08.64, 08.68, 08.72, 08.76, 08.80, 08.84, 08.88, 08.91, 08.95,
08.99, 09.03, 09.07, 09.11, 09.15, 09.19, 09.23, 09.26, 09.30, 09.34, 09.38, 09.42, 09.46, 09.50, 09.54, 09.57, 09.61, 09.65, 09.69, 09.73,
09.77, 09.81, 09.85, 09.89, 09.92, 09.96, 10.00, 10.04, 10.08, 10.12, 10.16, 10.19, 10.23, 10.27, 10.31, 10.35, 10.39, 10.43, 10.47, 10.50,
10.54, 10.58, 10.62, 10.66, 10.70, 10.73, 10.77, 10.81, 10.85, 10.89, 10.93, 10.97, 11.00, 11.04, 11.08, 11.12, 11.16, 11.20, 11.23, 11.27,
11.31, 11.35, 11.39, 11.43, 11.46, 11.50, 11.54, 11.58, 11.62, 11.66, 11.69, 11.73, 11.77, 11.81, 11.85, 11.89, 11.92, 11.96, 12.00, 12.04,
12.08, 12.11, 12.15, 12.19, 12.23, 12.27, 12.30, 12.34, 12.38, 12.42, 12.46, 12.49, 12.53, 12.57, 12.61, 12.65, 12.68, 12.72, 12.76, 12.80,
12.84, 12.87, 12.91, 12.95, 12.99, 13.03, 13.06, 13.10, 13.14, 13.18, 13.21, 13.25, 13.29, 13.33, 13.36, 13.40, 13.44, 13.48, 13.51, 13.55,
13.59, 13.63, 13.67, 13.70, 13.74, 13.78, 13.82, 13.85, 13.89, 13.93, 13.96, 14.00, 14.04, 14.08, 14.11, 14.15, 14.19, 14.23, 14.26, 14.30,
14.34, 14.38, 14.41, 14.45, 14.49, 14.52, 14.56, 14.60, 14.64, 14.67, 14.71, 14.75, 14.78, 14.82, 14.86, 14.90, 14.93, 14.97, 15.01, 15.04,
15.08, 15.12, 15.15, 15.19, 15.23, 15.26, 15.30, 15.34, 15.37, 15.41, 15.45, 15.48, 15.52, 15.56, 15.59, 15.63, 15.67, 15.70, 15.74, 15.78,
15.81, 15.85, 15.89, 15.92, 15.96, 16.00, 16.03, 16.07, 16.11, 16.14, 16.18, 16.22, 16.25, 16.29, 16.32, 16.36, 16.40, 16.43, 16.47, 16.51,
16.54, 16.58, 16.61, 16.65, 16.69, 16.72, 16.76, 16.79, 16.83, 16.87, 16.90, 16.94, 16.97, 17.01, 17.05, 17.08, 17.12, 17.15, 17.19, 17.22,
17.26, 17.30, 17.33, 17.37, 17.40, 17.44, 17.47, 17.51, 17.55, 17.58, 17.62, 17.65, 17.69, 17.72, 17.76, 17.79, 17.83, 17.86, 17.90, 17.94,
17.97, 18.01, 18.04, 18.08, 18.11, 18.15, 18.18, 18.22, 18.25, 18.29, 18.32, 18.36, 18.39, 18.43, 18.46, 18.50, 18.53, 18.57, 18.60, 18.64,
18.67, 18.71, 18.74, 18.78, 18.81, 18.85, 18.88, 18.92, 18.95, 18.98, 19.02, 19.05, 19.09, 19.12, 19.16, 19.19, 19.23, 19.26, 19.30, 19.33,
19.36, 19.40, 19.43, 19.47, 19.50, 19.54, 19.57, 19.60, 19.64, 19.67, 19.71, 19.74, 19.77, 19.81, 19.84, 19.88, 19.91, 19.94, 19.98, 20.01,
20.05, 20.08, 20.11, 20.15, 20.18, 20.22, 20.25, 20.28, 20.32, 20.35, 20.38, 20.42, 20.45, 20.48, 20.52, 20.55, 20.58, 20.62, 20.65, 20.68,
20.72, 20.75, 20.78, 20.82, 20.85, 20.88, 20.92, 20.95
};
//Temperature regulating software (PID).
int Heater_PID_Control(int input) {
//Calculate error term.
int error = adcValue_UR_Optimal - input;
//Set current position.
int position = input;
//Calculate proportional term.
float pTerm = -pGain * error;
//Calculate the integral state with appropriate limiting.
iState += error;
if (iState > iMax) iState = iMax;
if (iState < iMin) iState = iMin;
//Calculate the integral term.
float iTerm = -iGain * iState;
//Calculate the derivative term.
float dTerm = -dGain * (dState - position);
dState = position;
//Calculate regulation (PI).
int RegulationOutput = pTerm + iTerm + dTerm;
//Set maximum heater output (full power).
if (RegulationOutput > 255) RegulationOutput = 255;
//Set minimum heater value (cooling).
if (RegulationOutput < 0.0) RegulationOutput = 0;
//Return calculated PWM output.
return RegulationOutput;
}
//Displays the AFR value on an external narrowband lambda gauge with an (RC-filtered) 0-1V PWM signal from ANALOG_OUTPUT_PIN. 0V = AFR 20.00. 1V = AFR 10.00.
void UpdateAnalogOutput() {
//Local constants.
const float AirFuelRatioOctane = 14.70;
const int maximumOutput = 255; /* 5V */
const int minimumOutput = 0; /* 0V */
//Local variables.
int analogOutput = 0;
float lambdaAFR = Lookup_Lambda(adcValue_UA) * AirFuelRatioOctane;
//Convert lambda value to PWM output.
analogOutput = map(lambdaAFR * 100, 735, 2239, minimumOutput, maximumOutput);
//Make sure we do not exceed maximum values.
if (analogOutput > maximumOutput) analogOutput = maximumOutput;
if (analogOutput < minimumOutput) analogOutput = minimumOutput;
//Set PWM output.
analogWrite(ANALOG_OUTPUT_PIN, analogOutput);
}
//Lookup Lambda Value.
float Lookup_Lambda(int Input_ADC) {
//Declare and set default return value.
float LAMBDA_VALUE = 0;
//Validate ADC range for lookup table.
if (Input_ADC >= 39 && Input_ADC <= 791) {
LAMBDA_VALUE = pgm_read_float_near(Lambda_Conversion + (Input_ADC-39));
}
if (Input_ADC > 791) {
LAMBDA_VALUE = 10.119;
}
if (Input_ADC < 39) {
LAMBDA_VALUE = 0.750;
}
//Return value.
return LAMBDA_VALUE;
}
//Lookup Oxygen Content.
float Lookup_Oxygen(int Input_ADC) {
//Declare and set default return value.
float OXYGEN_CONTENT = 0;
//Validate ADC range for lookup table.
if (Input_ADC > 854) Input_ADC = 854;
if (Input_ADC >= 307 && Input_ADC <= 854) {
OXYGEN_CONTENT = pgm_read_float_near(Oxygen_Conversion + (Input_ADC - 307));
}
//Return value.
return OXYGEN_CONTENT;
}
//Function to set up device for operation.
void setup() {
//Set up serial communication.
Serial.begin(9600);
//Set up digital output pins.
pinMode(CJ125_NSS_PIN, OUTPUT);
pinMode(LED_STATUS_POWER, OUTPUT);
pinMode(LED_STATUS_HEATER, OUTPUT);
pinMode(HEATER_OUTPUT_PIN, OUTPUT);
//Set initial values.
digitalWrite(CJ125_NSS_PIN, HIGH);
digitalWrite(LED_STATUS_POWER, LOW);
digitalWrite(LED_STATUS_HEATER, LOW);
analogWrite(HEATER_OUTPUT_PIN, 0); /* PWM is initially off. */
analogWrite(ANALOG_OUTPUT_PIN, 0); /* PWM is initially off. */
//Start of operation. (Test LED's).
Serial.print("Device reset.\n\r");
digitalWrite(LED_STATUS_POWER, HIGH);
digitalWrite(LED_STATUS_HEATER, HIGH);
delay(200);
digitalWrite(LED_STATUS_POWER, LOW);
digitalWrite(LED_STATUS_HEATER, LOW);
//Start main function.
start();
}
void start() {
//Wait until everything is ready. Read CJ125 multiple times with delay in between to let it initialize. Otherwise responds OK.
int n = 0;
while (adcValue_UB < UBAT_MIN || n < 9) {
//Read input voltage.
adcValue_UB = analogRead(UB_ANALOG_INPUT_PIN);
//Delay and increment counter.
delay(100);
n++;
}
//Start of operation. (Start Power LED).
Serial.print("Device ready.\n\r");
digitalWrite(LED_STATUS_POWER, HIGH);
//Store calibrated optimum values.
Serial.print("Reading calibration data.\n\r");
//Let values settle.
delay(500);
//Store optimal values before leaving calibration mode.
adcValue_UA_Optimal = analogRead(UA_ANALOG_INPUT_PIN);
adcValue_UR_Optimal = analogRead(UR_ANALOG_INPUT_PIN);
//Update analog output, display the optimal value.
adcValue_UA = adcValue_UA_Optimal;
UpdateAnalogOutput();
//Present calibration data:
Serial.print("UA_Optimal (λ = 1.00): ");
Serial.print(adcValue_UA_Optimal);
Serial.print(" (λ = ");
Serial.print(Lookup_Lambda(adcValue_UA_Optimal), 2);
Serial.print(")\n\r");
Serial.print("UR_Optimal: ");
Serial.print(adcValue_UR_Optimal);
Serial.print("\n\r");
/* Heat up sensor. This is described in detail in the datasheet of the LSU 4.9 sensor with a
* condensation phase and a ramp up face before going in to PID control. */
Serial.print("Heating sensor.\n\r");
//Calculate supply voltage.
float SupplyVoltage = (((float)adcValue_UB / 1023 * 5) / 49900) * 149900;
//Condensation phase, 2V for 5s.
int CondensationPWM = (2 / SupplyVoltage) * 255;
analogWrite(HEATER_OUTPUT_PIN, CondensationPWM);
int t = 0;
while (t < 5 && analogRead(UB_ANALOG_INPUT_PIN) > UBAT_MIN) {
//Flash Heater LED in condensation phase.
digitalWrite(LED_STATUS_HEATER, HIGH);
delay(500);
digitalWrite(LED_STATUS_HEATER, LOW);
delay(500);
t += 1;
}
//Ramp up phase, +0.4V / s until 100% PWM from 8.5V.
float UHeater = 8.5;
while (UHeater < 13.0 && analogRead(UB_ANALOG_INPUT_PIN) > UBAT_MIN) {
//Set heater output during ramp up.
CondensationPWM = (UHeater / SupplyVoltage) * 255;
if (CondensationPWM > 255) CondensationPWM = 255; /*If supply voltage is less than 13V, maximum is 100% PWM*/
analogWrite(HEATER_OUTPUT_PIN, CondensationPWM);
//Flash Heater LED in condensation phase.
digitalWrite(LED_STATUS_HEATER, HIGH);
delay(500);
digitalWrite(LED_STATUS_HEATER, LOW);
delay(500);
//Increment Voltage.
UHeater += 0.4;
}
//Heat until temperature optimum is reached or exceeded (lower value is warmer).
while (analogRead(UR_ANALOG_INPUT_PIN) > adcValue_UR_Optimal && analogRead(UB_ANALOG_INPUT_PIN) > UBAT_MIN) {
//Flash Heater LED in condensation phase.
digitalWrite(LED_STATUS_HEATER, HIGH);
delay(500);
digitalWrite(LED_STATUS_HEATER, LOW);
delay(500);
}
//Heating phase finished, hand over to PID-control. Turn on LED and turn off heater.
digitalWrite(LED_STATUS_HEATER, HIGH);
analogWrite(HEATER_OUTPUT_PIN, 0);
}
//Infinite loop.
void loop() {
//Update analog inputs.
adcValue_UA = analogRead(UA_ANALOG_INPUT_PIN);
adcValue_UR = analogRead(UR_ANALOG_INPUT_PIN);
adcValue_UB = analogRead(UB_ANALOG_INPUT_PIN);
//Adjust PWM output by calculated PID regulation.
if (adcValue_UR < 500 || adcValue_UR_Optimal != 0 || adcValue_UB > UBAT_MIN) {
//Calculate and set new heater output.
HeaterOutput = Heater_PID_Control(adcValue_UR);
analogWrite(HEATER_OUTPUT_PIN, HeaterOutput);
} else {
//Turn off heater if we are not in PID control.
HeaterOutput = 0;
analogWrite(HEATER_OUTPUT_PIN, HeaterOutput);
}
//If power is lost, "reset" the device.
if (adcValue_UB < UBAT_MIN) {
//Indicate low power.
Serial.print("Low power.\n");
//Turn of status LEDs.
digitalWrite(LED_STATUS_POWER, LOW);
digitalWrite(LED_STATUS_HEATER, LOW);
//Re-start() and wait for power.
start();
}
//Display on serial port at defined rate. Comma separate values, readable by frontends.
if ( (100 / SERIAL_RATE) == serial_counter) {
//Reset counter.
serial_counter = 0;
//Calculate Lambda Value.
float LAMBDA_VALUE = Lookup_Lambda(adcValue_UA);
//Calculate Oxygen Content.
float OXYGEN_CONTENT = Lookup_Oxygen(adcValue_UA);
//Update analog output.
UpdateAnalogOutput();
//Output values.
Serial.print("Measuring, CJ125: 0x");
Serial.print(CJ125_Status, HEX);
Serial.print(", UA_ADC: ");
Serial.print(adcValue_UA);
Serial.print(", UR_ADC: ");
Serial.print(adcValue_UR);
Serial.print(", UBat_ADC: ");
Serial.print(adcValue_UB);
//Display lambda value unless out of range.
if (adcValue_UA >= 39 && adcValue_UA <= 791) {
Serial.print(", Lambda: ");
Serial.print(LAMBDA_VALUE, 2);
} else {
Serial.print(", Lambda: -");
}
//Display oxygen unless out of range.
if (adcValue_UA >= 307) {
Serial.print(", Oxygen: ");
Serial.print(OXYGEN_CONTENT, 2);
Serial.print("%");
} else {
Serial.print(", Oxygen: -");
}
//EOL.
Serial.print("\n\r");
}
}