Page 2 of 2
Re: CJ125 error code on homemade shield
Posted: 18 Jun 2020 01:33
by cristian2020
Hi Christian!, Very thanks You!!
with code correct:
1,0,10495,363,832,701,12392
1,0,10495,419,832,714,12461
1,0,10495,500,831,709,12536
1,0,10495,611,639,707,12453
1,0,10495,750,458,705,12409
2,0,10495,850,337,701,12385
2,0,10495,851,328,705,12381
2,0,10495,853,321,706,12377
2,0,10495,854,313,706,12370
2,0,10495,855,306,706,12364
2,0,10495,856,298,706,12357
2,0,10495,858,291,707,12353
2,0,10495,858,285,707,12347
2,0,10495,860,278,707,12342
2,0,10495,862,272,707,12338
now I can calculate Ip with Ip = 1000 (UA-1.5) /61.9*17 where: Ua = (ADC / 1023) right?}
Regrads,
Re: CJ125 error code on homemade shield
Posted: 18 Jun 2020 15:58
by Christian_Bylund
cristian2020 wrote: ↑18 Jun 2020 01:33
Hi Christian!, Very thanks You!!
with code correct:
now I can calculate Ip with Ip = 1000 (UA-1.5) /61.9*17 where: Ua = (ADC / 1023) right?}
Regrads,
That looks about right, except you UA need to be (ADC / 1023) * 5V.
See 4.1 in the
Technical Manual.
Good luck!
Re: CJ125 error code on homemade shield
Posted: 18 Jun 2020 20:14
by cristian2020
ok Perfect! Very thank you again!
Best Regards!
Re: CJ125 error code on homemade shield
Posted: 21 Jul 2020 16:20
by marvelousmatthew6969
hi christian iam wondering to know in the lambda sheild 2.0 what kinda mosfet are in use are its still the STD30nf06lt4 or difrent kinda mosfet thanks
best regards matthew
Re: CJ125 error code on homemade shield
Posted: 21 Jul 2020 18:37
by Christian_Bylund
marvelousmatthew6969 wrote: ↑21 Jul 2020 16:20
hi christian iam wondering to know in the lambda sheild 2.0 what kinda mosfet are in use are its still the STD30nf06lt4 or difrent kinda mosfet thanks
best regards matthew
Hi Matthew,
Lambda Shield 2 uses the same MOSFET as the original Lambda Shield.
Re: CJ125 error code on homemade shield
Posted: 22 Jul 2020 08:48
by marvelousmatthew6969
great thanks alot
Re: CJ125 error code on homemade shield
Posted: 22 Oct 2020 03:30
by cristian2020
Hi Christian, I hope you are fine.
I wasn't working on this project, but now I'm back. I remember the last time it worked good. But now the UR value doesn't change even when blowing directly on the sensor.
2,0,10495,1023,226,1023,12769
2,0,10495,1023,225,1023,12768
2,0,10495,1023,225,1023,12768
2,0,10495,1023,226,1023,12769
2,0,10495,1023,224,1023,12767
2,0,10495,1023,226,1023,12769
I am using lamda shield GUI code.
Any idea what is happening?
Re: CJ125 error code on homemade shield
Posted: 23 Oct 2020 16:19
by Christian_Bylund
Hi Cristian,
2,0,10495,1023,226,1023,12769
Besides UA being way too high and UR being too low I see another issue and that is the UB values. This indicates that you are powering your shield which a much too high voltage as you are reaching the limit of the ADC for the voltage divider used. This is one of the upgrades we did for Lambda Shield 2.
Check your supply voltage or ADC reference voltage.