Search found 266 matches
- 16 Jul 2024 20:20
- Forum: Lambda Shield for Arduino
- Topic: Dual O2 sensors on a selector switch to single display - Possible?
- Replies: 1
- Views: 686
Re: Dual O2 sensors on a selector switch to single display - Possible?
Christian, O2 system in the works is a single wideband sensor, Arduino, Shield, with a single OLED .96” display. Is in ‘85 911 3.2 with SSI exhaust that has a single bung on the 1-2-3 side. Am planning to add an O2 sensor to the 4-5-6 side. As the setup is, a single OLED display works nicely (takin...
- 16 Jul 2024 20:17
- Forum: Lambda Shield for Arduino
- Topic: No headers on shield
- Replies: 1
- Views: 54
Re: No headers on shield
Hi Christian... looking at your YouTube vids, the shield you are working with has headers. Was just setting up to bench test and my shield has no headers. Pardon me as I have only a small degree of Arduino experience so until I get the system working... I may stumble around and need more assistance...
- 09 Jul 2024 21:38
- Forum: Lambda Shield for Arduino
- Topic: Purchase
- Replies: 3
- Views: 408
Re: Purchase
Hi Karl, please check your email spam folder. You will find both your order confirmation and tracking number. I have also responded to your email.
Thank you.
Thank you.
- 02 Jul 2024 22:08
- Forum: Lambda Shield for Arduino
- Topic: Lambda Shield with OLED display
- Replies: 4
- Views: 364
Re: Lambda Shield with OLED display
Hi Christian, yes I'm using the Lambda-shield 2, I think I misunderstood your YT-Video that OLED- is implemented, but it's only implementd for the Lambda shield 1-code. Correct? best regsrad steffen Hi Steffen, The video is based on the original Lambda Shield. Functionality is the same but there is...
- 30 Jun 2024 17:07
- Forum: Lambda Shield for Arduino
- Topic: Lambda Shield with OLED display
- Replies: 4
- Views: 364
Re: Lambda Shield with OLED display
Hi, I'm using the Lambda Shield with an Arduino uno wifi and an IPhone since two years. Now I like to use the OLED display SSD1306. The display works with the test-code "Hello World", but with the sketch for the Shield only the "Bylund-logo" appears on the display and nothing fu...
- 16 Jun 2024 21:11
- Forum: Lambda Shield for Arduino
- Topic: 3.3V Usage
- Replies: 1
- Views: 988
Re: 3.3V Usage
Hello, how can I connect a module to a 3.3-volt board like Arduino Due or ESP boards, and do I need a logic level shifter for SPI or not? Also what steps should I take for voltage levels UR and UA? Regards The Bosch CJ125 used on the Lambda Shields have 5V interfaces, why go through all that troubl...
- 16 Jun 2024 20:55
- Forum: Lambda Shield for Arduino
- Topic: Enable Heater when engine start.
- Replies: 2
- Views: 755
Re: Enable Heater when engine start.
Hello, i want to ask if anyone know how can i read the temperature before satrt heating the sensor. I want to detect from temperature that the engine is starting so after that start heating the sensor. With this i think i can protect the sensors for failure Thank you Hello, there is actually a pre-...
- 15 Apr 2024 21:28
- Forum: Lambda Shield for Arduino
- Topic: W5200 and Lampda shield
- Replies: 3
- Views: 15348
Re: W5200 and Lampda shield
Hi Rob,
It seems both shields use the same default chip select pin for the SPI communication, D10. This is likely why neither shield works when stacked.
Hope it helps.
It seems both shields use the same default chip select pin for the SPI communication, D10. This is likely why neither shield works when stacked.
Hope it helps.
- 12 Apr 2024 21:32
- Forum: Lambda Shield for Arduino
- Topic: Lambda shield 2 stacking and height.
- Replies: 2
- Views: 20934
- 12 Apr 2024 21:16
- Forum: NOx Shield for Arduino
- Topic: NOx Shield Introduction.
- Replies: 4
- Views: 17566
Re: NOx Shield Power Supply.
Hello Christian I am new to using Nox Shield with Arduino board. I have an Arduino UNO R3 Set board. I have watched your instruction video many times I can see how you connect the wires from the Nox Sensor to the Nox Shield board, I am using a Bosch EGS-NX Sensor 24V but will be using it on cars. T...