Search found 259 matches
- 02 Jul 2020 20:39
- Forum: Knock Shield for Arduino
- Topic: Which knock IC to choose?
- Replies: 1
- Views: 9151
Re: Which knock IC to choose?
Are these identical or are there pros & cons to each? If the latter, what would they be? Hello DonP, thank you for liking our shields! The Renesas, previously Intersil HIP9011 is the original IC, Texas Instruments developed the TPIC8101 as a compatible IC . With the shield you will not find any...
- 30 Jun 2020 23:20
- Forum: Lambda Shield for Arduino
- Topic: Lambda Shield 2 installation
- Replies: 12
- Views: 36081
- 27 Jun 2020 23:24
- Forum: Lambda Shield for Arduino
- Topic: Lambda Shield 2 installation
- Replies: 12
- Views: 36081
Re: lambdaShield2 sketch & hardware
The power supply (a DC/DC Converter (5A)) in combination with a little PCB (30x13mm) is used to supress transients The shield will be installed in my YFM660R Raptor and later in my Corsa B. I used a schematic from VW for a T4-Bus for supression of transients. Greetz wolf Thank you for sharing if an...
- 27 Jun 2020 11:38
- Forum: Lambda Shield for Arduino
- Topic: Lambda Shield 2 installation
- Replies: 12
- Views: 36081
- 24 Jun 2020 11:20
- Forum: Lambda Shield for Arduino
- Topic: UR analog value does not change with temperature
- Replies: 5
- Views: 5813
Re: UR analog value does not change with temperature
If you send it to me I could verify the function. Preferably with sensor. It sounds like a faulty sensor.
- 24 Jun 2020 10:24
- Forum: Lambda Shield for Arduino
- Topic: UR analog value does not change with temperature
- Replies: 5
- Views: 5813
Re: UR analog value does not change with temperature
Since the Mosfet driver, which is connected both to the Heater mosfet and the CJ125_DIAGH through OUTA and OUTB respectively, the CJ125_DIAGH should have a PWM input. The diagnostic register does indeed gives me 0X28FF, and the heater is working, I can see the heating element starts to glow red. So...
- 24 Jun 2020 01:20
- Forum: Lambda Shield for Arduino
- Topic: UR analog value does not change with temperature
- Replies: 5
- Views: 5813
Re: UR analog value does not change with temperature
So something strange is happening with my Lambda UR values, I have a constant signal of 860 +- 5 that does not change with temperature, even if I trick the program to heat the sensor. Do you know what the UR output from the CJ125 is based on? Is it the reference resistor in the sensor? Hi, I believ...
- 22 Jun 2020 22:47
- Forum: Lambda Shield for Arduino
- Topic: Lambda Shield 2 installation
- Replies: 12
- Views: 36081
Re: lambdaShield2 sketch & hardware
To use an other power supply I thought about connecting Pin X6-4 direct with the 12-volt vehicle electrical system, cause the regulated power supply for the Arduino and LambaShield is connected over a 150µH inductance (+ a bidirectional ZVS-Diode between + and -) to the 12-volt vehicle electrical s...
- 21 Jun 2020 16:52
- Forum: Lambda Shield for Arduino
- Topic: Lambda Shield 2 installation
- Replies: 12
- Views: 36081
Re: lambdaShield2 sketch & hardware
Hello Wolf and thank you! 1: is it possible, to use an external power source for the heater, for example, direct from the battery of a car and the shield and arduino from an regulated power source? I assume you are referring to your Lambda Shield 2, this is described in the Technical Manual , 3.2 – ...
- 21 Jun 2020 15:40
- Forum: Lambda Shield for Arduino
- Topic: Compatibility of different models of LSU4.9
- Replies: 5
- Views: 6166
Re: Compatibility of different models of LSU4.9
I saw a LSU4.9 on the shopping website The model is 0 258 017 269 Is it available in Lambda Shield? Hi Liuyanting, it definitely looks like an LSU 4.9. I find no information on the internet about it. But I can tell you that it has the right connector. So I can not say by 100%, but most likely it is...